Clone-A-Willy Realistic Vibrator Silicone Penis Moulding Kit, Light Skin Tone

Product Information

As far as the finished product is concerned, neither the silicone base nor the catalyst contain any materials that disqualify them from being considered body-safe, so this is a 100% body safe DIY dildo project. For those curious about what the molding powder is made from and if it is safe to dunk your penis in it, it's made predominantly from a sodium alginate mixture with a few extra things thrown in to help it set properly. This mixture is non-toxic, contains no silica, and is completely hypo-allergenic. I've googled all of the ingredients myself and they all show up in normal products ranging from toothpaste to cosmetic products. One particular ingredient, calcium sulfate, shows up in some building materials but that makes sense judging how it solidifies into a solid mold once everything is said and done.

I texted James to see if he’d had success. Nope. He, too, struggled with the molding mixture, and his curved penis kept touching the sides of the tube. (If he’d been less impatient, he would’ve seen that the Clone-A-Willy kit offers a solution for men with curved penises.) I asked my friends: “Would a dildo of ‘myself’ make a good gift?” The response was a resounding “yes.” After my inquiry, my best friend, James, liked the idea so much that decided he, too, would craft a dildo for his girlfriend. At least I wouldn't be venturing into uncharted territory alone. Right around this point was when we started to realize we'd overlooked a crucial part of this plan: “ How does one make a dildo of one's penis?” Enter the Clone-A-Willy Kit

Clone-A-Willy

The bottom line is that you aren't going to feel any stinging or burning and there won't be any long term effects on your penis from using this kit. Pour out any water that has accumulated in the bottom of your mould and slowly pour into the silicone. This kit is kind of like making pancakes except the batter is going to go bad in 90 seconds and you have to keep a boner the whole time,” James quipped. At least he managed to make a mold of the top half of his penis, allowing him to create a stubby replica of his half-boner, a neon purple “dome” that now sits on his girlfriend’s coffee table. Learn From My Mistakes

My fantastic confidence in this endeavor and product waned considerably when I unfurled the poster-size directions. The four simple steps had transformed into more than a dozen, and the incredible specificity of each step had me in an immediate state of panic. Your Clone A Willy Kit comes in an 11 x 2½ inch clear plastic tube, into which you will insert your penis. If your penis is 9” or larger, or you want to make a non-vibrating dildo, keep reading! You'll need some extra materials! In lieu of a Valentine’s Day gift, I wrote my girlfriend a letter explaining what I’d gone through. I finished the letter with, “I tried, I failed, but I will not give up. I need your help, my love.”All standard kits include 8oz of our 2-part 100% platinum cure silicone. The colored silicone is added to the clear base to make the mixture that goes into your mold. See the chart above to determine whether you will need extra silicone or an XL Vibrator. I went through the steps more or less without a lot of fuss, but there are a couple things I will share with you that might alleviate some of your worries.

Now pour the water into a mixing bowl. This step is when the time sensitive parts begin, so make sure to pay attention. You will now cut open the bag of molding powder and stir it into the water for 45 seconds. It won't matter if the mix is a little lumpy still after 45 seconds, time is of the essence here and you just have 45 seconds to get everything mixed as well as you can. If you don't want to use the vibrator, you may need more silicone! Why? When inserted into the tube, the vibrator displaces the silicone. We took this extra volume into consideration when deciding how much silicone to include with our original kits. Once the mould has gelled, remove your one-eyed trouser snake while leaving the mould inside the tube. To get the most detail, let this sit for four hours before moving on. You then must hasten to shove your erect penis into the mixture "immediately," carefully avoiding touching the sides of tube. The tone of the directions—lighthearted and humorous—outline a process that required careful, diligent planning. As the impetuous man I am, directives such as, “Timing is very important!” stress me out, and I realized how unprepared I was for the Clone A Willy's litany of commands. How It Actually Worked

Press the tube against your body. The moulding gel will completely solidify in about two more minutes. Insert the silicone and cardboard assembly into the centre of the filled mould so that the cardboard rests flat against the top of the tube. Ensure to leave enough space for the vibrator to be added, or the mould may overflow. For those who love things a little frisky and risky, the perfect gift has revealed itself. With the help of this Clone-a-Willy Kit, a perfect silicone copy of either your or your partner's penis can be immortalised. It's a great gift for Valentine's Day or anniversaries or ideal to help spice things up in the bedroom. Be sure to use this product with a water based lubricant. Read the instructions carefully before using this product to avoid any unwanted side effects or reactions. Spice Up Your Sex Life Start your timer. Cut open the bag of white moulding powder, pour it into the bowl of water and start mixing. Stir no longer than 60 seconds. Tape around the edge of the tube. This will be pressed against your body, so you want it to be smooth.