Joined in 2023 
82 
63 About this deal
As I mentioned above, an electric balloon pump will make this process go by a lot faster, but you can always use a hand pump if that’s all you have around. Creating a balloon arch in times past was a long and tedious process. However, modernization has simplified the process so much that a balloon arch can be created in as little as 19 mins from start to finish and cost under twenty-five dollars. Alternatively, tape the empty length of the decorating strip directly to the wall, using masking or painter's tape.
There are three main methods for creating a balloon arch: balloons secured to a frame, balloons connected by fishing line, or balloons connected by balloon tape.Add small loops of fishing line throughout your balloon arch garland so you can hang them on the hooks you’ve prepared for placement. So, how to make a balloon arch? To make a balloon arch, there are a few different methods, depending on the design you’re hoping to achieve. You can choose to make a balloon arch by securing balloons onto a frame, or by securing the balloons to a fishing wire or balloon tape for a balloon arch garland. Pro Tapes ® History Dedicated to the development of high quality pressure sensitive tapes since 1977. Place the knotted end of the balloons through the hole so that they are firmly attached when forming the garland. Arrange them by color and size in a creative pattern, taking inspiration from the design you chose.
Some designs require additional accessories to recreate your masterpiece, take note of this so you can remember to get them for your project. Document the designs you like, this will help you later when its time to create your own. Choose the specific designs you are leaning towards and save them separately. Once you’ve gathered all of your supplies, follow the steps below to make a balloon arch stand with PVC pipe: Some people recommend using a low-heat glue gun instead of glue dots, but even on low heat, you may run the risk of ruining or popping some of your balloons. Glue dots are easier and safer to work with. The exact length of your PVC pipe pieces will vary. The key is to ensure that you have 3 PVC pieces instead of just 2, so there isn’t too much weight on a joint in the middle of the arch. Connect your 3 PVC pieces with the bell ends, then slip each regular end over the electrical conduits. The number of balloons you will need is dependent upon the size and fullness of your chosen balloon decoration arrangement. However, the general rule of thumb is for every foot of the balloon arch tape you will need 3 x 3 for three-color arch or 3 x 4 for a 4 color arch. balloons. To achieve your desired fullness, you can add more balloons later using balloon the dot tape. (link to this article for definition)You likely won’t need both balloon tape and fishing line – instead, you can choose one or the other, depending on the method you want to use. Take the next balloon, and pull it through the next hole. Alternate between different sizes of balloons to get the staggered effect. Also alternate between the sides of the strip to make the garland or arch look fuller. This can be easier to work with than trying to add balloons to a string, but it does leave a little more open gaps along the strand that will need filling in later. Are you having an event? Where in the planning process, are you? Are you looking for simple, trendy, and affordable decorating ideas? One of the most simple and inexpensive ideas you can bring to life at your next event is a balloon arch. What is a Balloon Arch
A balloon decorating strip, also called balloon arch tape or balloon garland strip, is a clear plastic strip, about 0.4" to 0.6" wide (1 cm to 1.5 cm), with evenly spaced out holes.Blow up all of your balloons using either your hand or electric pump. As mentioned above, I recommend using an electric balloon pump over a hand pump. It may cost a little extra, but it’s worth the investment. Tie up all of your balloons individually – no pairs here. You’ll also need to ensure that you’re blowing up some big balloons and some small balloons. With the floor flange securely in place, you can now screw in the 8” metal pipe. This will be the bottom part of your base. The first universal tip is not to overfill your balloons. It can be tempting to fill the balloon as large as it can go, but this will lead to more balloons popping and an uneven overall look. Pro Tip: While you can insert 5" balloons into the holes, they will "disappear" among the bigger balloons. It's best to keep the 5" balloons apart, and add them at the end with the help of glue dots or a cool melt glue gun (see step 5). Loop a piece of fishing line through one of the holes in the decorating strip, tie it off and attach the other end to the hook.
Great Deal 
New Comment