ESI ES2247B 2-Channel Multi Purpose Programmer (New Model)

Product Information

If you'll be updating or reflashing your ExpressLRS firmware into your device anyway, using a Binding Phrase is a no-brainer. a TX Module with version string of 3.1.2 will sync and work with a Receiver with firmware version 3.0.1

With the release of ExpressLRS v3.0, updating your Binding Phrase via the WebUI is an even more compelling reason to use a Binding Phrase. There is a 230 volt and 24 volt model it seems, this is the instructions. https://www.plumbase.co.uk/link/1/h002877_20563_t.pdf You can select a short and simple Binding Phrase for your devices before flashing or updating using the field in the ExpressLRS Configurator. However you say "Turned the thermostat right down but heating stayed on." which does not seem to point to the programmer. a TX Module with version string of 3.2.0 will NOT sync or bind with a Receiver with firmware version 2.4.0

It is designed primarily for separate control of your heating and stored hot water (S or Y plan). The heating and hot water programmes are independent of each other, giving you the opportunity to operate the system in the most energy-efficient and cost-effective manner. The new range of programmers hold a 3 year guarantee for consumer and installer peace of mind and are focused on value, quality and simplicity, offering an economical and durable solution for households. A Receiver flashed or set with a Binding Phrase WILL NOT initiate Manual Binding mode, however many times you try the procedure below. You must first reflash the receiver with the Binding Phrase field disabled and/or unset. Why would you not use a bind phrase though if you're already having to flash the RX anyway? If there is no other Full UART, you can try wiring a Pull-up Resistor: Connect a Resistor (300 Ohm to 1k Ohm value; a lower value is more effective) between this UART's RX pad and either a 5v or 3.3v pad as shown below: The ES2247B is a two channel multi purpose programmer with the flexibility of two or three on/off timings per day and can be configured for 7 day, 5/2 day or 24 hour operation for independent channels (all within the one unit), allowing one product to suit all installations alleviating any potential of incorrect selection.

If the button is being pressed or pinched, remove the cause of the pressing or pinching. Heatshrink can sometimes press a button on the receiver.If the ExpressLRS Lua Script is showing a C in the top-right corner alright, but then that line disappears and is replaced with a line saying "Model Mismatch", do not worry. ExpressLRS has detected that the set Model ID in the Receiver is different from the Receiver ID set in the current Model in your Radio Model Configuration. Older Radios or those with only one Menu Key will need to long-press the Menu Key to access the System Menu. You are now in the Tools Menu where Lua Scripts can be found. Scroll down and select ExpressLRS Lua Script. Disconnect the RX and TX wires of the Receiver from the Flight Controller. Reconnect power to the drone or aircraft. Observe the LED on the Receiver once again.

Records the default button state of the corresponding category & the status of CCPA. It works only in coordination with the primary cookie. The ESi Controls 2 Channel Programmer offers flexibility and reliability for use in any domestic heating and hot water installations. The ES2247B is a twin channel multi purpose programmer, designed for separate control of your heating and stored hot water. The heating and hot water programmes are independent of each other, giving you the opportunity to operate the system in the most energy efficient and cost effective manner. The new range of programmers hold a 3-year guarantee for consumer and installer peace of mind and are focused on value, quality and simplicity, offering an economical and durable solution for households.If you are using any of the Digital FPV systems like the DJI FPV Air Unit, Caddx Vista or DJI O3 Air Unit, and you wired or connected all six wires to your Flight Controller, you will need to remove the SBUS/DJI HDL wire. Power up your transmitter/radio and use the [BIND] button on the ExpressLRS Lua script, which sends out a binding pulse. The Popup will briefly show up and then disappear. Using the ExpressLRS Lua Script, look for a C in the top-right corner of the screen which indicates TX module and Receiver are Connected and Communicating. SPI-based Receivers on (official) Betaflight 4.3.1 and older will only sync or bind with ExpressLRS 2.x firmware

SPI-based Receivers on Betaflight 4.4.0 and newer will only sync or bind with ExpressLRS 3.x firmwareIt is designed primarily for separate control of your heating and stored hot water (S or Y plan). The heating and hot water programmes are independent of each other, giving you the opportunity to operate the system in the most energy efficient and cost effective manner. A C in the top-right corner should be visible indicating TX module and Receiver are connected and Communicating. a Receiver with version string of 3.1.2 will sync and work with a TX Module with firmware version 3.0.1