Silverline Water Level 10m (633586)

Product Information

Some insurance companies now offer discounts to those whos homes have water leak detection installed, particularly when insurance claims have been submitted for water damage before, so it’s worth mentioning to your insurance company if you have one fitted. In case of water loss, refill and adjust the device. Colours on images on different devices may vary. We cannot guarantee an exact match of the colour to the product. Fresh water and waste tank level kit from CBE consisting of a tank test panel with coloured LED indicators, tank probes and wiring harness. This kit is ideal if you are retro-fitting a water tank or if you don’t have a level monitoring facility as part of your 12V control system. The LEDs light up when the test button is pressed and indicate FULL, 2/3, 1/3 and RESERVE. Hold the hose ends at the same height. Allow the water level to equilibrate freely. Mark both levels of the surface of water on the hose.

Toolty Water Level Gauge Kit is used for leveling points that are far apart. Measuring tubes with a readable scale are made out of durable plastic (PVC). Tight plugs prevent the outflow of water at the place of measurements. The tube is then filled with water, except for a few inches at either end and they will both settle at the same level regardless of how close or far they are apart.When it comes to making your own water level, the type of tube is of high importance. You will need to ensure that it’s the correct length for your needs, so 50 – 70 feet should suffice and a diameter of 8 – 10mm will give enough movement for the water and allow a level to be clearly seen. Put on the end plugs. They will prevent an outflow of water to the place of measurements. After reaching the measurement levels, remove the plugs.

Step 1 – Fix to First Object – First, hold the tube up to the first object and then using either tape or screws, tape it or position screws either side to hold it in place so the top of the tube is level with the top of the object Fresh water tank probe is supplied with a gasket and mounting nut for fitting to a 60mm diameter hole in your water tank and the wiring harness connecting the probe to the test panel is 4m long. To save the job of making your own, you can actually buy a pre-made water level from most DIY stores such as the one below. However it is likely that it will cost a bit more than making one yourself. Yes, you can continue to return items as normal as long as you follow the government guidelines about leaving your house. But what if you need to level items such as fence posts over a long distance, or indeed around corners, obstacles or other structures. If you don’t have funds for an expensive laser level or tool that can do this this is where the water level comes into its own. Read on to find out about this fantastic tool. What is a Water Level?

Note: If using with tanks of a shallower depth than 400mm, the probe can be cut down to suit as follows: The job of marking is best done between 2 people so that both ends can be marked, so bear this in mind. We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.

Using water as a level in this manner has been done for many thousands of years and by many ancient civilizations including the Egyptians when building the pyramids so in terms of being a trustworthy method, it’s about as good and reliable as it gets.

Set Up And Using The Water Level

Step 3 – Allow to Settle – Before any marking can take place, allow the water level to completely settle so remove your thumb or bung from the end of the tube and let it level off until there is no movement at all Step 2 – Hold to Second Object – Holding your finger over the top of the tube, take the other end down to the object where you need to mark a level and hold in a "near enough" position towards the top of the object Fill the hose with water almost completely (leave columns of air about 5-10 cm long at the hose ends), while trying to prevent air bubbles from entering the hose. A complete leak detection kit to help protect a basement area or other vulnerable area in the home such as laundry rooms, central heating systems or other water pipes, from unexpected water leaks. Including a LeakStop alarm panel, connection cables, 3 metre sensor tape and optional shutoff valve (sizes available between 1/2″ and 2″). The only issues arise when external influences such as wind and the similar come into play as this causes water to move and thus upsets any levels. Tools and Products Needed for a Water Level

Before you can actually start levelling items with your water level you will first have to make it, if you’re not buying one. Follow the steps below to do so:

Step 5 – Mark Level Points – Before you start marking, the fluid in the pipe will not be flat, it will be concave as in the image below. You should agree with your help whether you are marking at the low point of the concave or the high point Step 2 – Prepare Water – Fill A suitable sized jug with water and add several drops of food colouring to to dye it. This will help to make it more visible in the tube Our collections by our couriers are happening as usual. As it stands, delivery times are not being affected too much. Please be aware though that Royal Mail and other couriers are sometimes prioritising essential items so please bear with us if your delivery takes slightly longer than expected.