SUPERWHOLE 12mm Equal Straight Compression Coupler Pipe Fitting Double Ferrule NEW

Product Information

Moving onto the other type of tubing, called hard tubing. Unlike the soft tubing, that is made of some sort of synthetic rubber or plastic, hard tubes can be made from a broad spectrum of materials. The most common hard tubes for liquid cooling are acrylic (plexiglass) or PETG (polyethylene terephthalate). They are cheap, easy to come by, and can be shaped and bent in every household. There are tools available which can make acrylic and PETG bending really easy, but we will not elaborate on that subject now, we will leave that for another article as hard tube bending is considered to be a more advanced loop building method. If you are welding or adapting a system, you may want to opt for brass fittings instead. Are stainless steel compression fittings ok for domestic use?

At Plumb Parts our range of compression fittings are suitable for a broad spectrum of applications across the domestic, industrial and commercial sectors. Plastic push-fit joints on copper pipes break the continuity of a plumbing system's earth bonding. You must restore this by joining the two copper pipes with a length of 4mm2 single-core earth cable, secured by earth clamps. Capillary joints While in the early days we had simple barb fittings, nowadays the market has narrowed down to only compression type fittings. While barb fittings are still available for workstation purposes and applications where the aesthetics are not a key point, the market is dominated by compression type fittings. The compression fittings themselves are divide into two major categories which are, Soft Tubing Compression and Hard Tubing Compression fittings, or for short STC and HDC. Soft Tubing Compression FittingsWe would wrap up this article at this moment, although we are certain that we didn’t cover all the small details. As we said at the start, this subject is very broad, there are many choices, but we hope that we managed to cover the basics. In one of the future articles, we will cover the subject of angled adaptersand other special connectors, such as T-Splitters and Ball Valves! The existence of pre-bent tubes and rising popularity distro plates, building with hard tubes have never been easier. As a matter of fact, a lot of the newcomers to custom loop liquid cooling have built their first loop using distro plates and hard tubing. We are more than happy to give you a hot tip that EK is working on bringing pre-bent tubes to the product portfolio. We also promise that we will cover distro plates in more detail with one of our upcoming blog posts. What is G1/4″?

Fittings are manufactured from high-quality brass materials which ensure a permanently tight and secure connection, without the use of special tooling or additional sealant. These fittings are suitable for connecting a wide range of tubes, including copper tubes in accordance with EN 1057, carbon steel to EN 10305, stainless steel to EN 10312 and plastic pipes to BS 7291, EN 15875 and EN 15876. Using a spanner, tighten the nut over the threaded head of the fitting, while holding the fitting with a pair of plumber’s grips. This pressure created by the tightening motion will press down on the olive, causing it to grip the pipe tightly. However, be careful not to exert too much pressure as this could damage the fitting or thread, making the device harder to remove or reposition Straight Couplers , Reducing Couplers , Male Couplers , Female Couplers , Elbows 90 deg , Wallplate Elbows , Long Radius Elbows , Angled Wallplate Adaptors ,Stop Ends, Straight Tap Connectors , Bent Tap Connectors , Tees , Reduced Branch Tee , Both Ends Reduced Tee , Reduced End Tee , Reduced End and Branch Tee , Straight Cylinder Union , Bent Cylinder Union All-In-One Affordable, easy to install, maintenance-free liquid cooler with class-leading performanceThe other, less common hard tubes can be made out of copper, brass, borosilicate glass and nowadays even carbon tubes are coming into fashion. The potential problem with these materials is that bending them is not possible or bending requires special tools. We say the „potential problem“ because skilled and more advanced users actually prefer these luxurious materials because the loop can still be connected just by using more adapter fittings and more joints. Swagelok-certified trainers are available to teach courses on topics such as Tube Fitting Installation and Tube Fitting Inspection at locations and times convenient to you. The colleting region better isolates stress risers at the tube grip to resist bending, deflection, and vibration. The mechanical nature of Compression joints is well-proven technology that is extremely robust and resilient. There is no significant difference. Compression fittings designed for liquid will work fine with gas but if you use optional PTFE tape, make sure it is gas grade. In addition, ensure the fittings are accessible and not hidden behind walls or under floors. Are Compression Fittings Reliable?