White - UPVC Shiplap Cladding 45mm Drip Trim

Product Information

When making your calculations ensure you allow for a full trim for each edge run. Jointing trims along the same area can look very untidy. It is better to have a continuous single trim for each edge. Methods of fitting a cladding trim A half-clad room, bath panel, or where your cladding would meet a skirting could use an end cap to finish off the edge. In most situations, a trim will be needed to cover untidy cuts or gaps around external edges, internal corners, wall to ceiling cladding, or simply to complement the cladding edges. Cladding trims provide a clean look rather than using just silicone which can provide the inconsistent finish. You must be careful and take your time while cutting to ensure you don’t damage the profile of the trim. Cladding trims will allow you a bit of freedom when it comes to your edges. You wont have to worry about getting the edges perfect as you will have a decorative trim to cover any mishaps and gaps.

In some cases trims can be fitted at the same time as your cladding. How to fit cladding trims before your cladding

Long-life, low-maintenance and attractive solution.

Please note: it is recommended to leave a gap of 10mm between the Perforated Closure and the base of your in stallation, to ensure a necessary gap for airflow. The Perforated Closure needs to be perfectly level before fixing to the wall, as a Start Profile Trim will be fixed to the Perforated Closure. If your Perforated Closure is not fitted parallel, you may be at risk of unlevel cladding. Using a measuring square to cut your mitred joints in your cladding trims can sometimes be the simplest method.

This is to be mounted on the bottom of the installation - before the boards have been fitted - to provide a weather drip to angle any water away from the mounting wall. This can be used with either the 100mm V Joint or the 150mm Shiplap. The Cladding Drip Trim will usually be used above a door or window head to deflect any running water away from the opening which can be useful during periods of adverse weather. This trim is 5 metres in length and should be used in conjunction with 150mm Shiplap or 100mm V Joint Cladding and is suitable for external use on buildings as a decorative and protective facing. We supply everything you’ll need to cap off your cladding project, including starter trims, edge trims, butt joints and more. View our full cladding trims range below for products that will maintain their beauty and performance for many years to come. Have More Questions About Cladding Trims?Fitting certain cladding trims first will give you a guideline and support when installing your cladding panels. Uneven walls that bow or taper towards one end may prove difficult for even the most avid DIYer to cut to, which may result in gaps. With trims, these edges do not have to be perfect, as whichever trim is needed will cover most gaps in a decorative fashion. Why should I fit cladding trims? Inserting cladding into a corner cladding trim will hold your panel into the corner while you fix it to the surface.Theres no need to worry about cutting your edges perfect as the internal trim will cover up all of the rough edges.

With some cladding trims it may be easier to fit afterwards, such as external corners and coving trims. How to fit cladding trims after you have fitted your claddingYou're able to select a preferreddelivery date in your shopping basket. Whilst we aim to deliver your items on this date, it is not guaranteed. The only trims you can fit before the cladding are internal trims, coving trims and some types of external trims. Below are the most important points to consider when taking your measurements: Do you require a mitred corner or edge to allow for trimming corners? Fitting your cladding trims after you have fitted the panels can be a lot easier in some situations.

Trims are used to finish off any untidy corners or edges that would have otherwise been exposed once you had finished fitting your cladding, perhaps your ceiling is uneven and you don’t have the necessary time or skill to scribe each individual panel to fit the bumps and dips in 08-the adjoining surface, that is where trims come in. They cover up a multitude of sins without the need to cover with silicone. We recommend taking this into account when calculating your wastage. Ensuring you aren’t short on trims when it comes to fitting. The Eurocell Building Plastics products supplied by Eurocell Profiles Ltd are produced in accordance with a BS EN 1SO

Embossed Cladding

Once you have fitted your trims give them a wipe down with a damp cloth or cleaning wipe to remove any excess adhesive or dust. Recommended tools for fitting